Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 152

Page: 152 / 320

Interface

Table 5.27 WRITE SAME (2/2)

Byte(hex) Name Value

Description

0C to13

Count

(8 byte)

Number of Sectors

14 to17

Pattern

(4 byte)

If the Function Code is 0001h, this field contains a
32-bit pattern that is written on the media.

18 to 1FF

(Reserved)

Reserved

* It is invalid excluding the description value.

Table 5.28 ERROR RECOVERY CONTROL

Byte(hex) Name Value

Description

00, 01

Action Code

0003h

ERROR RECOVERY CONTROL

0001h

Set New Value

The retry processing when making an error in the
specified timer

02, 03

Function

Code

0002h

Return Current Value

The timer value of the error recovery being set now is
displayed in SN /SC field.

0001h Read

Timer

04, 05

Selection

Code

0002h Write

Timer

06, 07

Value

(2 byte)

Set to Timer Value (x 100 ms)

Minimum value is 5 sec.

(ex.)

0000h: Disable timeout

0031h: Invalid

0032h: 5000 ms (5 s)

08 to 1FF

(Reserved)

Reserved

* It is invalid excluding the description value.

5-78

C141-E280

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Search results

Summary of Contents for MHZ2080BJ

Reviews:

Related manuals for MHZ2080BJ

Brands by name

Popular brands

Fujitsu MHZ2080BJ, Product/Maintenance Manual

Search results

Summary of Contents for MHZ2080BJ

Reviews:

Related manuals for MHZ2080BJ

Brands by name

Popular brands