manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 157 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 157

 

5.3  Host Commands 

• 

SCT WRITE DATA (SN = E1h, FR = D6h) 

This command writes the data of the number of sectors for which the data 
specified with SCT SET COMMAND and number of sectors specified Sector 
Count Field. 

28-bit command 

At command issuance (Shadow Block Registers setting) 

CM 1 

1 

0 

1 

1 

1 

1 

1 

DH x 

x 

x 

DV 

xx 

CH 

CL 

SN 

SC 

FR 

Key (C2h) 

Key (4Fh) 

E1h 

xx 

D6h 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH x 

x 

x  DV 

xx 

CH 

CL 

SN 

SC 

ER 

xx 

xx 

xx 

xx 

Error information 

SCT WRITE DATA Command issue procedure. 

1.  Issue the SCT set command of action code 0002h and function code 0002h. 

2.  Issue the SCT write command and the write data is transmitted to the device. 

 

 

 

C141-E280 

5-83 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments