manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 174 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 174

Interface 

 

(23)  READ BUFFER (X 'E4') 

The host system can read the current contents of the data buffer of the device by 
issuing this command. 

Upon receipt of this command, the device transfers the PIO Setup.  After that, the 
host system can read up to 512 bytes of data from the buffer. 

• 

Error reporting conditions 

(1)  A SATA communication error occurred (ST = 51h, ER = 0Ch). 

 

At command issuance (Shadow Block Registers setting contents) 

CM 

1 1 1 0 0 1 0  0 

DH 

x 

x x 

x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

xx 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

x x x x 

xx 

CH 

CL 

SN 

xx 

Error information 

SC 

ER 

xx 

xx 

xx 

 

5-100 

C141-E280 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments