manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 211 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 211

 

5.3  Host Commands 

(35)  READ NATIVE MAX ADDRESS (X 'F8')  

This command posts the maximum address intrinsic to the device, which can be 
set by the SET MAX ADDRESS command. Upon receipt of this command, the 
device indicates the maximum address in the DH, CH, CL and SN field. Then 
reports the status to the host system. 

• 

Error reporting conditions 

(1)  A SATA communication error occurred (ST = 51h, ER = 14h). 

At command issuance (Shadow Block Registers setting contents) 

 

CM 

1 1 1 1 1 0 0  0 

DH 

x L x x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

xx 

 

At command completion (Shadow Block Registers contents to be read) 

 

ST Status 

information 

DH 

x x x x  Max 

head/LBA 

[MSB] 

CH 

CL 

SN 

SC 

ER 

CYL No. [MSB] / LBA 

CYL No. [LSB]  / LBA 

SCT No. 

/ LBA[LSB] 

xx 

Error information 

 

C141-E280 

5-137 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments