Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 191

Page: 191 / 320

5.3 Host Commands

*29 WORD 128

Bits 15-9: Reserved

Bit 8:

Security level. 0: High, 1: Maximum

Bits 7-6:

Reserved

Bit 5:

'1' = Enhanced security erase supported

Bit 4:

'1' = Security counter expired

Bit 3:

'1' = Security frozen

Bit 2:

'1' = Security locked

Bit 1:

'1' = Security enabled

Bit 0:

'1' = Security supported

*30 WORD 206: SCT Command Transport

Bits 15-6: Reserved

Bit 5:

'1' = SCT Data Tables supported.

Bit 4:

'1' = SCT Features Control supported.

Bit 3:

'1' = SCT Error Recovery Control supported.

Bit 2:

'1' = SCT Write Same supported.

Bit 1:

'1' = SCT Long Sector Access supported.

Bit 0:

'1' = SCT Command Transport supported

*31 WORD 210-211: Write Read Verify Sector Count Mode 3 Only.

The number of sectors to be verified

If Write Read Verify features set is enabled. (Mode 3)

Value:

400h – 40000h sectors

*32 WORD 212-213: Write Read Verify Sector Count Mode 2 Only.

The number of sectors to be verified

If Write Read Verify features set is enabled. (Mode 2)

Value: 10000h

sectors

C141-E280

5-117

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Search results

Summary of Contents for MHZ2080BJ

Reviews:

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 191 / 320

Search results

Summary of Contents for MHZ2080BJ

Reviews: