manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 55 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 55

 

3.3  Connections with Host System 

3.3.4  SATA interface cable connection  

The cable that connects the disk drive to the host system must be compliant with 
the Serial ATA Revision 2.6 specification.  

3.3.5  Note about SATA interface cable connection 

Take note of the following precaution about plugging a SATA interface cable into 
the SATA interface connector of the disk drive and plugging the connector into a 
host receptacle: 

 

When plugging together the disk drive SATA interface connector 
and the host receptacle or SATA interface cable connector, do not 
apply more than 10 kgf of force in the connection direction once 
they are snugly and securely in position. 
 
 

 

Connecting/removing the cable without releasing the SATA 
interface Latch may lead to connector damage and the loss of the 
Latch function.  Accordingly, be sure to connect/remove the cable 
while releasing the Latch. 
 
 

 

 

C141-E280 

3-11 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments