Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 137 | Manualshive

Page: 137 / 320

background image

5.3 Host Commands

•

Off-line data collection capability

Indicates the method of off-line data collection carried out by the drive. If the off-
line data collection capability is 0, it indicates that off-line data collection is not
supported.

Table 5.14 Off-line data collection capability

Bit Meaning

0

If this bit is 1, it indicates that the SMART EXECUTE OFF-
LINE IMMEDATE sub-command (Features field = D4h) is
supported.

1 Vendor

unique

2

If this bit is 1, it indicates that offline data collection under
execution is aborted when a new command is received.

3

If this bit is 1, it indicates that the SMART Off-line Read
Scanning Technology is supported.

4

If this bit is 1, it indicates that the SMART Self-test function
is supported.

5

If this bit is 1, it indicates that the SMART Conveyance Self-
test is supported.

6

If this bit is 1, it indicates that the SMART Selective Self-test
is supported.

7 Reserved

bits

•

Failure prediction capability flag

Table 5.15 Failure prediction capability flag

Bit Meaning

0

If this bit is 1, it indicates that the attribute value is saved on
media before the drive enters the power save mode.

1

If this bit is 1, it indicates that the attribute value is saved
automatically after the pre-set operation of the drive.

2 to 15

Reserved bits

C141-E280

5-63

«
...
135
136
137
138
139
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

Brand: Quest Leisure Products Pages: 22

Brand: GrainPro Pages: 19

Brand: NEC Pages: 254

Brand: Sako Pages: 19

Catalina KC-103

Brand: SPAREHAND Pages: 2

Brand: Silverline Pages: 2

Brand: Synology Pages: 28

Brand: DataDirect Networks Pages: 118

Brand: Husky Pages: 10

Brand: HP Pages: 1

Brand: IBM Pages: 141

WD10000E035 - Elements Desktop

Brand: Western Digital Pages: 2

WD GREEN WD15NPVX

Brand: Western Digital Pages: 55

Brand: Sun Microsystems Pages: 34

Brand: Sharp Pages: 15

Brand: Siemens Pages: 2

Brand: Siemens Pages: 40

Gigaset USB Stick 108

Brand: Siemens Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands