Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 144 | Manualshive

Page: 144 / 320

background image

Interface

•

Current Span under test

As the self-test progress, the device shall modify this value to contain the test span
number currently being tested.

•

Feature Flags

Table 5.22 Selective self-test feature flags

Bit Description

0

Vendor specific (unused)

1

When set to one, perform off-line scan after selective test.

2

Vendor specific (unused)

3

When set to one, off-line scan after selective test is pending.

4

When set to one, off-line scan after selective test is active.

5 to 15

Reserved

Bit [l] shall be written by the host and returned unmodified by the device. Bit [3:4]
shall be written as zeros by the host and the device shall modify them as the test
progress.

•

Selective Self-test pending time [min]

The selective self-test pending time is the time in minutes from power-on to the
resumption of the off-line testing if the pending bit is set.

•

SMART Command Transport (SCT)

This command supports the following functions by using the SMART command
according to the value specified for the SN field and the FR field. Moreover,
WRITE LOG EXT/READ LOG EXT is used in 48-CMD environment.

5-70

C141-E280

«
...
142
143
144
145
146
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

Azure StorSimple 8100

Brand: Microsoft Pages: 12

Brand: SentrySafe Pages: 2

Brand: Orico Pages: 27

1.8" StoreJet Portable HDD 20GB (TOSHIBA) TS20GSJ18

Brand: Transcend Pages: 6

Brand: Quantum Pages: 2

Brand: Sun Microsystems Pages: 36

FUSION LITTER BIN

Brand: Glasdon Pages: 4

Storage Master Solarguard Building

Brand: ClearSpan Pages: 51

Storage Master Solarguard Series

Brand: ClearSpan Pages: 51

Brand: Cybernetics Pages: 190

Brand: Lenze Pages: 58

Brand: FreeNAS Pages: 36

Brand: Western Digital Pages: 2

Brand: Sjobergs Pages: 2

Brand: ECOSAFE Pages: 7

Brand: VERITAS Pages: 5

9Z6-00001 - 360 Hard Drive 120 GB Removable

Brand: XBOX Pages: 10

Brand: Galaxy Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands