Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 199 | Manualshive

Page: 199 / 320

background image

5.3 Host Commands

*4)

Automatic Acoustic Management (AAM)

The host writes to the Sector Count filed with the requested acoustic management
level and executes this command with subcommand code 42h, and then Automatic
Acoustic Management is enabled. The AAM level setting is preserved by the
drive across power on and COMRESET.

AAM Level

Sector Count Filed

Performance mode (Fast Seek)
Acoustic mode (Slow Seek)
Abort
Non Operate

C0h-FEh

80h-BFh

01h-7Fh

00h, FFh

High-speed seek to which gives priority to the performance operates as for
"Performance mode", and low-speed seek by which the seek sound is suppressed
operates as for "Acoustic mode".

Setting the seek mode by this command is applied to the seek operation in all
command processing.

*5)

Write-Read-Verify feature (optional)

SN SC

Description

00h (Mode 0)

-

Enabled Always

01h (Mode 1)

-

The first 65,536 logical sectors written by the host
after every spin-up (or reset) or after issuing this
set features shall be verified.

02h (Mode 2)

-

Device may determine, for itself, how many logical
sectors to do.

03h (Mode 3)

Verify count

The first (Verify Sector Count x 1024) logical
sectors written by the host after every spin-up or
after issuing this set features shall be verified.

04h-FFh -

Reserved

(Abort)

C141-E280

5-125

«
...
197
198
199
200
201
...
»

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments

Related manuals for MHZ2080BJ

XCubeNAS XN7012R

Brand: Qsan Pages: 16

grand Hard Disk

Brand: LaCie Pages: 2

BLACKOUT WINDOW STORAGE SYSTEM

Brand: REBEL OFF ROAD Pages: 9

Brand: Macally Pages: 37

Brand: PARYA Pages: 6

Brand: KREAFUNK Pages: 34

RX343-S BLK/SLV

Brand: Rosewill Pages: 2

Brand: Swiss Aqua Technologies Pages: 5

Brand: Accordance Systems Pages: 58

Brand: Fast Mover Pages: 2

Brand: Seagate Pages: 20

Brand: Newpo Pages: 5

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands