manualshive.com logo in svg

Fujitsu MHZ2080BJ, Product/Maintenance Manual, Page: 127 / 320

Share
Download
Fujitsu MHZ2080BJ Product/Maintenance Manual Download Page 127

 

5.3  Host Commands 

(15)  SLEEP  (X '99' or X 'E6') 

This command is the only way to make the device enter the sleep mode. 

Upon receipt of this command, the device enters the sleep mode, then reports the 
status to the host system.  The device reports the status even if the device has not 
fully entered the sleep mode. 

In the sleep mode, the spindle motor is stopped. 

The only way to release the device from sleep mode is to execute a software or 
COMRESET. 

• 

Error reporting conditions 

(1)  A SATA communication error occurred (ST = 51h, ER = 14h). 

 

At command issuance (Shadow Block Registers setting contents) 

CM 

X '99' or X 'E6' 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

xx 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

ER 

xx 

xx 

xx 

xx 

Error information 

 

C141-E280 

5-53 

Summary of Contents for MHZ2080BJ

































































































































































































































































































































Reviews:

No comments