Fujitsu AB* A12GATH Service Manual Download Page 68

Page: 68 / 241

3-6 FUNCTION

03-16

3-6-1 Auto Restart

The air conditioner restarts with the previous setting operation.

3-6-2 Icing Protection Control

3-6-3 Oil Recovery Operation

[Oil recovery operation] : It periodically returns the residual refrigerant ion oil in the indoor unit and the connection

piping back to the outdoor unit , and prevents the compressor oil level from decreasing.

6 sec ON 2 sec OFF Blinking

Indoor unit LED : Operation LED

Indoor fan : Same operation before oil recovery operation.
Indoor EEV : Control pulse

During the above operation, a refrigerant noise may be from the indoor unit.

The icing of the indoor heat exchanger is prevented during the cooling and dry mode operation.

(1) Starting Condition

Compressor is operation more than 3 minutes.

When "Heat exchanger inlet temperature T

" continues *4 minutes or more.

Compressor is operation more than 3 minutes.

When "Heat exchanger outlet temperature T

" continues 4 minutes or more.

(2) Operation

EEV is closed.

Fan is at the setting amount.

(3) Completing Condition

Heat exchanger inlet and middle temperature T

After more than 5 minutes

Drain pump turns off at 60 minutes past the completion of the icing protection operation.

1°C

7°C

Summary of Contents for AB* A12GATH


















































































































































































































































Search results

Summary of Contents for AB* A12GATH

Reviews:

Related manuals for AB* A12GATH

Brands by name

Popular brands

Fujitsu AB* A12GATH, Service Manual

Search results

Summary of Contents for AB* A12GATH

Reviews:

Related manuals for AB* A12GATH

Brands by name

Popular brands