Fujitsu AB* A12GATH Service Manual Download Page 153

Page: 153 / 241

Detective Actuators:

Detective details:

Forecast of Cause :

1. 3-way valve not opened 2. Outdoor unit ambient temperature too low

3. Outdoor unit fan operation defective, foreign matter at heat exchanger

4. EEV defective, strainer clogged 5. Solenoid valve defective 6. 4-way valve defective

7. Low pressure sensor characteristics defective 8. Insufficient refrigerant

Suction pressure sensor

"Protection stop by "suction pressure 15psi (0.10MPa)continued for 10 minutes"

or "suction pressure 7.25psi (0.05MPa)" during operation of any compressor""

was generated 5 times within 3 hours

No foreign matter in air passage?
Heat exchange fins clogged
Fan rotates?
Outdoor unit fan motor check

Check Point 3 :

Check the outdoor unit fan operation, heat exchanger

Check Point 2 : Check the outdoor unit ambient temperature

Outdoor ambient temperature lower than operating range?

Outdoor unit EEV1, EEV2 operation check
Strainer not clogged?

Refer to "Service Parts Information 14,15 ".

Check Point 4 : Check the outdoor unit EEV, strainer clogging

Indoor unit EEV operation check
Strainer not clogged?

Check Point 4 : Check the indoor unit EEV, strainer clogging

Suction pressure sensor characteristics check

* For the characteristics of the suction pressure sensor,

refer to "Service Parts Information 22".

Check Point 7 : Check the suction pressure sensor

Check Point 8 : Check the refrigerant amount

Leak check

Check Point 6 : Check the solenoid valve (SV1)

Solenoid valve operation check

Refer to "Service Parts Information 17".

Check Point 1 : Check if 3-way valve is open.

If the 3-way valve was closed, open the

3-way valve and check operation.

Check Point 1 : Check if 3-way valve is open.

If the 3-way valve was closed, open the

3-way valve and check operation.

After fixing the problem and for canceling the Error, Error Reset (F3-40) will be required after power reset

<Cooling

operation>

<Heating

operation>

Check Point 5 : Check the 4-way valve (4WV1, 4WV2, 4WV3)

4-way valve operation check.

Refer to "Service Parts Information 18".

Indoor Unit : Operation LED 9 times Flash, Timer LED 15 Times Flash,

Filter LED Continuous Flash.

Outdoor Unit : E. A 5. 1

Error Code : 9 U / A 6

Indicate or Display:

Trouble shooting 65 EA5. 1

OUTDOOR UNIT Error Method:

Low Pressure Abnormal

04-77

Summary of Contents for AB* A12GATH


















































































































































































































































Search results

Summary of Contents for AB* A12GATH

Reviews:

Brands by name

Popular brands

Fujitsu AB* A12GATH, Service Manual

Search results

Summary of Contents for AB* A12GATH

Reviews:

Brands by name

Popular brands