manualshive.com logo in svg

Fujitsu AB* A12GATH, Service Manual

Share
Download
Fujitsu AB* A12GATH Service Manual Download Page 173

Trouble shooting  88

Peripheral device FAN not operate

OK

LED ON

LED Blinking

Forecast of  Cause :

1. Power supply failure                                    2. Trouble on peripheral device

3. DX-Kit Electrical compornent defective     4. Field setting mismatch

Check Point 1 : Power supply

Check Point 2 : LED indication on the controller PCB

Check Error code indication on the

remote controller or Service tool

Is not the breaker down?

Instant drop ---------------------- Check if there is a large load electric apparatus in the same circuit.

Momentary power failure ----- Check if there is a defective contact or leak current in the power supply circuit.

Noise ----- Check if there is any equipment causing harmonic wave near electric line 

                  (Neon bulb or electric equipment that may cause harmonic wave).

                 Check the complete insulation of grounding.

Check circuit on the terminal ON /OFF SIGNAL(OUTPUT)

04-97

Short circuit

Short circuit

Refer to the service manual for

the peripheral device

and check the trouble shooting tips.

Check Point 3 : Operation signal output

Check circuit on the terminal FAN SIGNAL (OUTPUT)

Check Point 4 : FAN SIGNAL output

Open circuit

Open circuit

Check power input CN800 Pin1 - Pin2

OK (DC12V)

Make sure that the operation command 

(ON signal) is transfering from the controller to

the DX-Kit controller.

If the ON singal was OK, Replace the Relay PCB.

Check Point 5 : Relay PCB power input DC12V

Other tips

NG

Make sure that the operation command (ON signal) is 

transfering from the Controller to the DX-Kit controller.

If the ON singal was OK, Replace the Main PCB.

Check Field function setting, (External input signal setting)

The Prohibit setting condtions

The operating mode mismatch

General check procedure

   1. Check Error code on the VRF system. (Remote controller, Service tool, etc)

   2. Check LED brinks on the controller PCB of DX-KIT

   3. Check Error code on the peripheral device.

   4. Check non of wrong filed settings or wrong installation.

   5. Check if FAN operation stopped by the freeze prevention or the defrosting operation.

Summary of Contents for AB* A12GATH


















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands