manualshive.com logo in svg

Fujitsu AB* A12GATH, Service Manual

Share
Download
Fujitsu AB* A12GATH Service Manual Download Page 180

If the amount of recovered refrigerant is available that was pulled out of outdoor unit which compressor 

was replaced.

(When the refrigerant is recovered by refrigerant recovery machine, and its weight is measured.)

If the amount of recovered refrigerant from outdoor unit that compressor was replaced is not sure.

(When the refrigerant leakage was the case.)  

>>> Once recover all units' refrigerant, and recharge the calculated amount of refrigerant 

        (Original amount and additional amount)  again after vacuuming.

Note: To use the recovered refrigerant is not recommended in case of refrigerant leakage.

           Always charge fresh refrigerant with correct amount for the system after repairing.

>>> Perform vacuuming of repaired outdoor unit thoroughly, and add the refrigerant with the recovered 

       amount.

2. Refrigerant charging after the compressor replacement.

Connect the high pressure service port of the broken master unit and the low pressure pipe of the broken

 master unit by pressure gauge.

>>> Refrigerant release from the heat exchanger of the broken master unit.

        (Refrigerant is removed until refrigerant shortage is resolved)

<How to respond, when refrigerant is deficient>

Reuse the refrigerant of the broken master unit.

Broken

master unit

Substitutional

master unit

Slave

unit #1

All 3 Way-Valves Close

Open and adjust

High pressure (service port)

Liquid

Gas 

Recover the remaining refrigerant in the broken master unit from the service port(s).

 

2

When new refrigerant is added to the operating system, check the weight of additional refrigerant,and 

adjust the total refrigerant amout after repairing.

04-104

Summary of Contents for AB* A12GATH


















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands