manualshive.com logo in svg

Fujitsu AB* A12GATH, Service Manual

Share
Download
Fujitsu AB* A12GATH Service Manual Download Page 144

OK

OK

OK

1. Driver PCB defective        2. Fan motor defective        3. Main PCB defective    

4. Lose connection  or disconnecting wire

Driver PCB

Fan motor

Main PCB

Check Point 1 : Check the wiring connection

Check Fan motor to Driver PCB wiring connector disconnection, open

Check Main PCB to Driver PCB wiring connector disconnection, open

Check Driver PCB to Capacitor wiring connector disconnection, open

Check Point 2 : Check DC input power of Driver PCB

Check the DC voltage of CN759 is within 15V+ 10%.  Refer to the service parts info 5

>> If it is abnormal, replace Main PCB.

     (When Main PCB is replaced, set up the original setting by Rotary, Dip, and Push SW)

Check Point 4 : Replace Fan motor

Indoor Unit     :  Operation LED 9 times Flash, Timer LED 15 Times Flash, 

                            Filter LED Continuous Flash.

Outdoor Unit  :  E. 9 7. 9

Error Code      : 9 U  / 9 7

Outdoor Unit Fan Motor Driver 

Abnormal

Trouble shooting  56                 E97. 9

Indicate or Display:

Detective Actuators:

Detective details:

OUTDOOR UNIT Error Method:

Forecast of Cause : 

When Driver PCB detects the following abnormalities, 

the error signal is output.

   Driver PCB defective

   Fan motor defective (Layer short)

   Main PCB defective (DC output abnormal)

   Lose connection  or disconnecting wire

Check the winding resistance of Fan motor.
Change Fan motor and check if the error reoccurs on a test run.

After fixing the problem and for canceling  the Error, Error Reset (F3-40) will be required after power reset

-

Check Point 3 : Replace Driver PCB

Check the appearance and condition of mounting of Driver PCB.
Change Driver PCB and release the error.

Check if the error reoccurs on a test run.

Caution

 By changing of DIP SW 4-2 to ON,  the Back-up operation can start when the active outdoor unit exists on the multi outdoor unit connection.

  (Stand alone outdoor unit is impossible)

 The following conditions will be concerned in use of back-up operation. (Please do not use the system with back-up operation for long time.)

  - The operating compressor life time becomes shorter.

  - The operating performance may drop due to the limited active compressor(s). 

  - The compressor may stop frequently by protection controlling.

  *In order to keep the operating capacity, the release of the Low noise mode setting might be necessary.

04-68

Check blown fuse of DC FAN motor (5A FUSE)

Summary of Contents for AB* A12GATH


















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands