Fujitsu AB* A12GATH Service Manual Download Page 73

Page: 73 / 241

03-21

1. Initialization

2. Operation Control

When starting up

Automatic operatic control

Automatic PI control is performed based on the indoor unit heat exchanger outlet temp and inlet temp.

Discharge airflow temperature control

The discharge airflow temperature is controlled so that it reaches to the set-up temperature based on the difference

between the discharge airflow temperature and the set-up temperature.

Cooling operation: 1) If the discharge airflow temperature becomes 5°C lower than the set-up temperature,

EEV is fully closed.

2) If the suction airflow temperature becomes 0.5°C lower than the set-up temperature,

EEV is fully closed.

Heating operation: If the suction airflow temperature becomes 0.5°C higher than the set-up temperature,

EEV is fully closed.

3. Special Control

(1) When cooling and refrigerant circulation starts, the drain pump starts simultaneously.

(2) The drain pump operates continuously for 3 minutes after the refrigerant circulation stopped.

(3) When the refrigent circulation is stopped by a start of indoor heat exchanger frost prevention

operation, the drain pump will turn off in 1 hour after the end of indoor heat exchanger frost

prevention operation.
(4) When the water level in the drain pan rises up and then the float switch functions:

Microcomputer stops the refrigerant circulation and indoor fan motor operation.

Drain pump operates continuously for 3 minutes after the float switch is turned off.

(Almost condensing water may be drained)

(5) When the float switch turns ON continuously for 3 minutes, 'FAILURE INDICATION' operates.

(6) When the float switch turns OFF within 3 minutes, the unit starts cooling operation.

When the power is turned ON.

When it has passed the limited time since the last initialization.

When indoor unit stopping by Thermo-OFF condition.

Oil recovery operation : Controlled pulse(Maximum 1400 puls)

Test run operation : Controlled pulse.

Freeze prevention control : Fully closed.

Vacuuming operation : Fully open.

Defrost operation : Controlled pulse(Maximum 1400 puls)

3-7-4 ELECTRONIC EXPANSION VALVE CONTROL for DX-KIT

3-7-5 DRAIN PUMP OPERATION for DX-KIT

Outdoor unit Condition

EEV Condition

Cooling
Heating

Fully closed
Fully closed

(Cooling) Move to the cooling control base pulse in steps.

(Heating) Move to the heating control base pulse in steps.

OFF

Fully closed

Summary of Contents for AB* A12GATH


















































































































































































































































Search results

Summary of Contents for AB* A12GATH

Reviews:

Related manuals for AB* A12GATH

Brands by name

Popular brands

Fujitsu AB* A12GATH, Service Manual

Search results

Summary of Contents for AB* A12GATH

Reviews:

Related manuals for AB* A12GATH

Brands by name

Popular brands