manualshive.com logo in svg

Fujitsu AB* A12GATH, Service Manual

Share
Download
Fujitsu AB* A12GATH Service Manual Download Page 151

OUTDOOR UNIT Error Method:
High Pressure Abnormal

1. 3-way valve not opened

2. Outdoor unit fan operation defective, foreign matter at heat exchanger, excessive ambient

    temperature rise                                     3. EEV defective, strainer clogged

4. Solenoid valve defective                        5. 4-way valve (including a coil) defective  

6. Discharge pressure sensor defective    7. Refrigerant overcharged

Judgment from value sensed by discharge 

pressure sensor

"Protection stop by "discharge pressure     580psi(4.00MPa)during operation of 

 any compressor"" generated 3 times within 60 minutes.

 I

f the same operation (High pressure protection stop) generated 3 times

 within 30 minutes, compressor stops permanently.

EEV operation check
Check of strainers before and after EEV

Refer to "Service Parts Information 13".

Check Point 3 : Check the EEV, strainer (indoor unit)

No foreign matter in air passage?
Heat exchange fins clogged
Outdoor unit fan motor check
Ambient temperature not raised by effect of other heat sources?
Discharged air not sucked in?

Check Point 2 : Check the outdoor unit fan operation, 

                          heat exchanger, ambient temperature

Discharge pressure sensor characteristics check

* For the characteristics of the discharge pressure sensor, refer to "Service Parts Information 22".

Check Point 6 :Check the discharge pressure sensor

Check Point 7 : Check the refrigerant amount

Refrigerant charged amount check

Check Point 5 : Check the solenoid valve (SV1, SV2)

Check Point 3 : Check the EEV, strainer

Solenoid valve operation check. Refer to "Service Parts Information 17".

Indoor Unit     :  Operation LED 9 times Flash, Timer LED 15 Times Flash, 

                           Filter LED Continuous Flash.

Outdoor Unit  :  E. A 4. 1

Error Code      :  9 U  /  A 4

OK

OK

OK

OK

OK

OK

Check Point 1 : Check if 3-way valve is open.

If the 3-way valve was closed, open the 

3-way valve and check operation.

Check Point 1 : Check if 3-way valve is open.

If the 3-way valve was closed, open the 

3-way valve and check operation.

OK

OK

Forecast of Cause : 

Trouble shooting  63                 EA4. 1

Indicate or Display:

Detective Actuators:

Detective details:

<Cooling

 

operation>

<Heating

 

operation>

EEV (EEV1, EEV2) open?
Strainer clogging check (before and after EEV, ACM, oil return)

Refer to "Service Parts Information 14, 15".

Check Point 4 : Check the 4-way valve (4WV1, 4WV2, 4WV3)

4-way valve operation check. Refer to "Service Parts Information 18".

Caution

 By changing of DIP SW 4-2 to ON,  the Back-up operation can start when the active outdoor unit exists on the multi outdoor unit connection.

  (Stand alone outdoor unit is impossible)

 The following conditions will be concerned in use of back-up operation. (Please do not use the system with back-up operation for long time.)

  - The operating compressor life time becomes shorter.

  - The operating performance may drop due to the limited active compressor(s). 

  - The compressor may stop frequently by protection controlling.

  *In order to keep the operating capacity, the release of the Low noise mode setting might be necessary.

04-75

Summary of Contents for AB* A12GATH


















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands