manualshive.com logo in svg

Fujitsu AB* A12GATH, Service Manual

The Fujitsu AB* A12GATH Service Manual is a comprehensive user guide that provides step-by-step instructions for optimizing the performance of your Fujitsu AB* A12GATH product. Easily downloadable and completely free, this manual is available exclusively on our website, ensuring quick access to all the necessary information you need to maximize your device's potential.

Share
Download
background image

Outdoor Temp Sensor Error

OK

Outdoor temp. sensor

Outdoor temp. sensor short or open detected

1. Connector connection defective, open

2. Sensor defective

3. Main PCB defective

OK

Check Point 1 : Check the connector connection and cable open

Connector connection state check
Cable open check

Check Point 2: Check the sensor

Sensor characteristics check (Disconnect the sensor from the PCB and check.)

* For the sensor characteristics, refer to the "Service Parts Information 24".

Check Point 3 : Check voltage of Main PCB (DC5.0V)

Main PCB (CN144:1-3) voltage value = 5V

Remove the sensor from Main PCB, check the voltage.

Outdoor temp. sensor (CN144:1-3)

Indoor Unit     :  Operation LED 9 times Flash, Timer LED 15 Times Flash, 

                            Filter LED Continuous Flash.

Outdoor Unit  :  E. 7 4. 1

Error Code      :  9 U  /  7 4

If the voltage does not appear, replace Main PCB and set up original address.

Trouble shooting  41             E74. 1

Indicate or Display:

Detective Actuators:

Detective details:

OUTDOOR UNIT Error Method:

Forecast of Cause : 

1

2

3

BLACK

BLACK

THERMISTOR (OUT TEMP.)

CN144

Caution

 By changing of DIP SW 4-2 to ON,  the Back-up operation can start when the active outdoor unit exists on the multi outdoor unit connection.

  (Stand alone outdoor unit is impossible)

 The following conditions will be concerned in use of back-up operation. (Please do not use the system with back-up operation for long time.)

  - The operating compressor life time becomes shorter.

  - The operating performance may drop due to the limited active compressor(s). 

  - The compressor may stop frequently by protection controlling.

  *In order to keep the operating capacity, the release of the Low noise mode setting might be necessary.

1

2

3

04-53

DC

Summary of Contents for AB* A12GATH


















































































































































































































































Reviews:

No comments

Related manuals for AB* A12GATH

Panasonic WH-ADC0309H3E5 Operating Instructions Manual preview
WH-ADC0309H3E5
Brand: Panasonic Pages: 108
Data Aire gForce Ultra Installation, Operation And Maintenance Manual preview
gForce Ultra
Brand: Data Aire Pages: 64
Data Aire gForce Ultra Installation, Operation & Maintenance Manual preview
gForce Ultra
Brand: Data Aire Pages: 123
aldes ZRT-IL Installation Operation & Maintenance preview
ZRT-IL
Brand: aldes Pages: 4
Daikin SkyAir FBQ18PVJU Installation Manual preview
SkyAir FBQ18PVJU
Brand: Daikin Pages: 18
Trane BAYECON103AA Installer'S Manual preview
BAYECON103AA
Brand: Trane Pages: 17
Carrier 38ESA Installation And Start-Up Instructions Manual preview
38ESA
Brand: Carrier Pages: 12
Carrier 40VMM007A Installation And Maintenance Instructions Manual preview
40VMM007A
Brand: Carrier Pages: 26
Zephir ZRP12000CB Manual preview
ZRP12000CB
Brand: Zephir Pages: 44
Electra WMZ Series Service Manual preview
WMZ Series
Brand: Electra Pages: 151
Uberhaus MWK-15CRN1-BJ7 User Manual preview
MWK-15CRN1-BJ7
Brand: Uberhaus Pages: 29
GE AEH12AR Owner'S Manual And Installation Instructions preview
AEH12AR
Brand: GE Pages: 40
SecureAire Platinum ACS1620-PLT Installation And User Manual preview
Platinum ACS1620-PLT
Brand: SecureAire Pages: 16
Diva RDW 9RN Installation Manual preview
RDW 9RN
Brand: Diva Pages: 20
Danby DAC6011E Owner'S Use And Care Manual preview
DAC6011E
Brand: Danby Pages: 35
Lennox iHarmony 10C16 Installation Instructions Manual preview
iHarmony 10C16
Brand: Lennox Pages: 16
Daikin Split Comfora R32 Service Manual preview
Split Comfora R32
Brand: Daikin Pages: 164
Mitsubishi Mr. Slim PEA-A12AA4 Installation Manual preview
Mr. Slim PEA-A12AA4
Brand: Mitsubishi Pages: 28

Brands by name

Popular brands

Load more brands