Fujitsu AB* A12GATH Service Manual Download Page 177

Page: 177 / 241

1. Stop the operation, and turn off the all outdoor units.

1-1. Backup operation when compressor of the master unit is defective.

[Procedure]

(Example: Three outdoor units are connected.)

2. Fully shut off the 3-way valve (Liquid, Gas) of the broken master unit.

3. Set the

Slave unit #1

as a new master unit, and make up the system of two outdoor units.

5. Uncouple the transmission connector between the broken master unit and indoor units,

and connect it into the slave unit #1 (substitutional master unit).

7. Turn on the units except the broken master unit, and wait for more than 30 seconds.

(Do not turn on the broken master unit)

8. It is ready for Backup operation.

Start operation as usual.

1. Method of backup operation

SERVICE INFORMATION

Backup Operation

4-4 SERVICE INFORMATION

Backup operation is the operating method of replacing compressor while the system is running.

Compressor can be replaced without stopping the system.

Details :

In backup operation, cooling and heating capacity is decreased by the capacity

of the separated outdoor unit.
The work procedure is as follows.

Change the setting of the DIP SW 3-1 / 3-2 (Outdoor unit address setting) of the slave

unit #1, from [ ](slave unit #1) to [ ](

Master unit

Change the setting of the DIP SW 3-3 / 3-4 (Number of slave units connected setting)

of the slave unit #1, from [ ](zero unit) to [ ](one unit).

6. Change the setting of the DIP SW 5-1/ 5-2 (Number of outdoor unit) of the slave unit #1 (substitutional

master unit) and #2 (substitutional slave unit #1), from [ON/ OFF](3) to [OFF/ ON](2).

4. Set up the

Slave unit #2

as the slave unit #1.

Change the DIP SW 3-1/ 3-2 (Outdoor unit address setting) of the slave unit #2,

from [ON/ OFF](slave unit #2) to [OFF/ ON](

Slave unit #1

4-4-1 Backup operation

OFF / ON

OFF / OFF

OFF / ON

( Make sure the pressure equalization has been finished.)

04-101

Summary of Contents for AB* A12GATH


















































































































































































































































Search results

Summary of Contents for AB* A12GATH

Reviews:

Brands by name

Popular brands

Fujitsu AB* A12GATH, Service Manual

Search results

Summary of Contents for AB* A12GATH

Reviews:

Brands by name

Popular brands