Fujitsu AB* A12GATH Service Manual Download Page 136

Page: 136 / 241

Discharge Pressure Sensor Error

Forecast of Cause :

Check Point 3 : Check voltage of Main PCB (DC5.0V)

CN118

PRESSURE SENSOR (HIGH)

1 2 3

1 2 3

Discharge pressure sensor

When any of the following conditions is satisfied, a discharge pressure

sensor error is generated.

1. 30 seconds or more have elapsed since the outdoor unit power was turned

on and pressure sensor detected value 0.3V continued for 30 seconds

or more

2. 30 seconds or more have elapsed since the outdoor unit power was turned

on and pressure sensor detected value 5.0V was detected.

1. Discharge pressure sensor connector disconnection, open

2. Discharge pressure sensor defective

3. Main PCB defective

Check Point 1 : Check the discharge pressure sensor connection state

Connector connection state check

Cable open check

Check Point 2 : Check the discharge pressure sensor

Sensor characteristics check

* For the characteristics of the discharge pressure sensor,

refer to the "Service Parts Information 22".

Main PCB (CN118:1-3) voltage value = 5V

Remove the sensor from Main PCB, check the voltage.

Discharge pressure sensor (CN118:1-3)

Indoor Unit : Operation LED 9 times Flash, Timer LED 15 Times Flash,

Filter LED Continuous Flash.

Outdoor Unit : E. 8 6. 1

Error Code : 9 U / 8 6

If the voltage does not appear, replace Main PCB and set up original address.

Trouble shooting 48 E86. 1

Indicate or Display:

Detective Actuators:

Detective details:

OUTDOOR UNIT Error Method:

Caution

By changing of DIP SW 4-2 to ON, the Back-up operation can start when the active outdoor unit exists on the multi outdoor unit connection.

(Stand alone outdoor unit is impossible)

The following conditions will be concerned in use of back-up operation. (Please do not use the system with back-up operation for long time.)

- The operating compressor life time becomes shorter.

- The operating performance may drop due to the limited active compressor(s).

- The compressor may stop frequently by protection controlling.

*In order to keep the operating capacity, the release of the Low noise mode setting might be necessary.

04-60

Summary of Contents for AB* A12GATH


















































































































































































































































Search results

Summary of Contents for AB* A12GATH

Reviews:

Related manuals for AB* A12GATH

Brands by name

Popular brands

Fujitsu AB* A12GATH, Service Manual

Search results

Summary of Contents for AB* A12GATH

Reviews:

Related manuals for AB* A12GATH

Brands by name

Popular brands