Fuji Xerox ApeosPort-V 6080 Administrator'S Manual Download Page 549 | Manualshive

Page: 549 / 745

background image

Error Code

549

Pro

b

lem

So
lv

in

g

15

Note

•

If you cannot resolve an error despite following the instructions described in the table, contact our
Customer Support Center. The contact number is printed on the label or card attached on the
machine.

Other Errors

This section describes the remedies when the following messages are displayed.

133-710

[Cause]

When printing the received fax document, the paper loaded on the bypass tray was
used for printing because the specified tray could not be used.

[Remedy] Take one of the following measures:

z

Load paper available for printing the received fax document.

z

Use a paper type available for printing the received fax document:
plain paper, bond paper, recycled paper, side 2 paper, user-defined custom paper.

z

Confirm the settings by selecting [Tools] > [Fax Service Settings] > [Fax Control] >
[Receiving Paper Size].

1)Select [Receiving Paper Size] > [Tray Mode] to add a tray to be used for printing the

received fax documents.

2)Set up paper so that the tray specified for [Tray Mode] can be used for printing the

received fax documents.

If the error still is not resolved, contact our Customer Support Center.

Error Code

Cause and Remedy

Error

Message

Cause and Remedy

A fault has occurred.
Switch off the machine.
(xxx-yyy)

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the touch screen is blank, and

then switch the machine power on again.
If the message persists, record the content displayed for [(xxx-yyy)]. Then
immediately switch the main power and power off, make sure that the touch
screen is blank, and then contact our Customer Support Center.

Completed with an
error.
(xxx-yyy)

[Cause]

An error occurred, and the operation terminated abnormally.

[Remedy] Execute the operation again.

A fault has occurred.
The machine has
rebooted. Select
[Close]. If the problem
persists, call for service.
(xxx-yyy)

[Cause]

An auto-recoverable internal error occurred, and the machine restarted
automatically.

[Remedy] Select [Close] to use the machine normally. If the error still is not resolved,

contact our Customer Support Center.

«
...
547
548
549
550
551
...
»

Summary of Contents for ApeosPort-V 6080










































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 6080

Brand: Xerox Pages: 34

Brand: WaxJet Pages: 131

Brand: EBS Pages: 34

Brand: Oki Pages: 147

Brand: Oki Pages: 12

Brand: Oki Pages: 297

Brand: Oki Pages: 111

Brand: Oki Pages: 6

Brand: Oki Pages: 2

Brand: Oki Pages: 108

C5800Ldn Series

Brand: Oki Pages: 266

C5800Ldn Series

Brand: Oki Pages: 276

Brand: Oki Pages: 12

Brand: Oki Pages: 354

Brand: Oki Pages: 78

Brand: Oki Pages: 328

Brand: Oki Pages: 24

Brand: Oki Pages: 719

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands