Faulhaber 3564K024B CS Instruction Manual Download | Manualshive

Page: 53 / 92

background image

53

4 Functional Description

4.8 Technical information

4.8.1 Sinus commutation

The 3564K024B CS and the MCBL 3003/06 S are characterised by a so-called sinus commutation. This
means that the preset rotating field is always ideally positioned in relation to the rotor. As a result,
torque fluctuations can be reduced to a minimum, even at very low speeds. In addition, the motor
runs particularly quietly.
In the current version, the sinus commutation has been enhanced to include so-called flat-top modu-
lation, which enables 15 % more modulation. As a result, higher no-load speeds are possible.
With the SIN0 command, the system can even be set so that over 30 % more modulation is possible.
In this mode, the sinus commutation in the upper speed range switches over to a block commuta-
tion. This full modulation enables the complete speed range of the motor to be utilised.

Command Function

Description

SIN

Sinus commutation

0: Full modulation

1: Limited to sinusoidal form (basic setting)

4.8.2 Current regulator and I

2

t current limitation

The FAULHABER Motion Controllers are equipped with an integral current controller, which enables
implementation of moment limitation.
The following parameters can be set:

Command Function

Description

LPC

Load Peak Current Limit

Load peak current
Value: 0 to 12 000 mA

LCC

Load Continuous Current Limit

Load continuous current
Value: 0 to 12 000 mA

CI

Load Current Integral Term

Load integral term for current controller
Value: 1...255

1.) Peak current
FAULHABER command:

LPC8000

… Set peak current to 8000 mA

The current is limited to the peak current, provided that the thermal current model calculates a non-
critical temperature.

2.) Continuous current
FAULHABER command:

LCC2800

… Set continuous current to 2800 mA

If the thermal current model reaches a critical temperature, continuous current is switched to.

Mode of operation of the current controller:
When the motor starts, the peak current is preset as the set-point for the current controller. As the
load increases, the current in the motor constantly increases until it finally reaches the peak current.

«
...
51
52
53
54
55
...
»

Summary of Contents for 3564K024B CS





























































































Reviews:

No comments

Related manuals for 3564K024B CS

Brand: ABB Pages: 30

Brand: ABB Pages: 15

Brand: ABB Pages: 10

Brand: ABB Pages: 44

Brand: ABB Pages: 2

Brand: Bartlett Pages: 30

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: Aalborg Pages: 128

Brand: IBM Pages: 105

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: Gardigo Pages: 8

Brand: Gardigo Pages: 19

Brand: WAREMA Pages: 4

Brand: YASKAWA Pages: 49

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands