Faulhaber 3564K024B CS Instruction Manual Download | Manualshive

Page: 36 / 92

background image

36

4 Functional Description

4.4 Enhanced operating modes

Example:
Motor should turn 1/1000th of a revolution for each input signal:

STW1
STN1000

The acceleration and speed values (AC, DEC, SP) are also taken into account in step motor mode.
These permit gentle starting and deceleration. The position range limits set via LL can also be acti-
vated with the APL1 command.

4.4.2 Gearing mode (electronic gear)

Gearing mode enables the use of an external encoder as set-point source for the position.

Command Function

Description

GEARMOD Gearing Mode

Change to gearing mode

The two channels of an external encoder are connected to connections AnIn and AGND, which may
need to be connected to the 5 V encoder supply via a 2.7 k



pull-up resistor.

The gear ratio can be set in accordance with the following formula:

Revolutions = pulses

STW

STN

Revolutions

… Revolutions that are generated on the drive

Pulses

… actually counted pulses which result in quadrature signal processing

STW

… Step width (step width factor = number of steps per encoder pulse)

STN

… Step number (number of steps = number of steps per revolution)

Value range of STN and STW: 1 to 65 535

Command Function

Description

STW

Load Step Width

Load step width for step motor and gearing mode

STN

Load Step Number

Load number of steps per revolution for step motor

and gearing mode

Example:
Motor has to move one revolution at 1000 pulses of the external encoder:

STW1
STN1000

The direction of rotation can be predefined with the commands ADL and ADR, or via an external
signal at the fault pin (DIRIN command).
The acceleration and speed values (AC, DEC, SP) are also taken into account in gearing mode. These
permit gentle starting and deceleration. The position range limits set via LL can also be activated
with the APL1 command.

«
...
34
35
36
37
38
...
»

Summary of Contents for 3564K024B CS





























































































Reviews:

No comments

Related manuals for 3564K024B CS

Brand: UE Pages: 4

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 20

Brand: Ubisys Pages: 2

Brand: Galcon Pages: 32

Brand: Radarcan Pages: 40

Brand: Eaton Pages: 100

Brand: Jabra Pages: 8

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: Omega Pages: 44

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

MusicCAST MCX-CA15

Brand: Yamaha Pages: 176

Brand: Zamel Pages: 2

Brand: KanDao Pages: 265

Waukesha Cherry-Burrell D4 Series

Brand: SPX FLOW Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands