manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 74 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 74

     

Doc

#    

E154713     

                              

              4-2

4: Electrical Installation

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

For sustained loads greater than 10 amps, the CT wires should be wired directly 
through the CT opening (pass through wiring method - see Section 4.3), using 10 
AWG wire.

L’installation des compteurs de Nexus 1500+ doit être effectuée 
seulement par un personnel qualifié qui suit les normes relatives aux
précautions de sécurité pendant toute la procédure. Le personnel doit 
avoir la formation appropriée et l'expérience avec les appareils de 
haute tension. Des gants de sécurité, des verres et des vêtements de 

protection appropriés sont recommandés.

Pendant le fonctionnement normal du compteur Nexus 1500+ des tensions dangere-
uses suivant de nombreuses pièces, notamment, les bornes et tous les transforma-
teurs de courant branchés, les transformateurs de tension, toutes les sorties, les 
entrées et leurs circuits. Tous les circuits secondaires et primaires peuvent parfois 
produire des tensions de létal et des courants. Évitez le contact avec les surfaces sous 
tensions. Avant de faire un travail dans le compteur, assurez-vous d'éteindre l'alimen-
tation et de mettre tous les circuits branchés hors tension.

Ne pas utiliser les compteurs ou sorties d'appareil pour une protection pri-
maire ou capacité de limite d'énergie. Le compteur peut seulement être util-
isé comme une protection secondaire.

Ne pas utiliser le compteur pour application dans laquelle une panne de compteur 
peut causer la mort ou des blessures graves.

Ne pas utiliser le compteur ou pour toute application dans laquelle un risque 
d'incendie est susceptible.

Toutes les bornes de compteur doivent être inaccessibles après l'installation.

Ne pas appliquer plus que la tension maximale que le compteur ou appareil relatif 
peut résister. Référez-vous au compteur ou aux étiquettes de l'appareil et les spécifi-
cations de tous les appareils avant d'appliquer les tensions. Ne pas faire de test 
HIPOT/diélectrique, une sortie, une entrée ou un terminal de réseau. 

EIG nécessite l'utilisation de les fusibles pour les fils de tension et alimentations élec-
triques, ainsi que des coupe-circuits pour prévenir les tensions dangereuses ou 

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments