manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 69 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 69

     

Doc

#    

E154713     

                              

              3-13

3: Hardware Installation

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

12. Use a non-conductive tweezer to gently lift the Positive (+) tab up. See Figure 

3.14.

Figure 3.14: Lifting the Positive Tab

NOTE: 

Always keep the plus (+) side of the battery up.

13. Using a gloved hand and observing the correct battery polarity (plus (+) side up), 

gently slide the battery under the Positive (+) tab. Push the battery all the way into 
the battery holder. See Figure 3.15.

 Figure 3.15: Inserting the Battery

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments