manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 209 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 209

     

Doc

#    

E154713     

                              

              11-25

11: Using the I/O Options

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

11.8.7.1: Overview

The Relay Output module consists of four latching relay outputs. In Normal mode, the 
device accepts commands to control the relays. Relay Output modules are 

triggered by limits programmed with the Communicator EXT

TM

 software. See the 

Communicator EXT

TM

 4.0 and MeterManager EXT Software User Manual 

for details on 

programming limits.

Each latching relay will hold its state in the event of a power loss.

11.8.7.2: Communication

Maximum registers per request, read or write, is 4 registers.

The device operates with the following default parameters:

Address

247 (F7H)

Baud Rate

57600 Baud

Transmit Delay Time

20 msec

11.8.7.3: Normal Mode

Normal mode consists of one process: the device accepts new commands to control 
the relays.

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments