Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 186

Page: 186 / 322

Doc

E154713

11-2

11: Using the I/O Options

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

2. There is a plastic "track" on the top and the bottom of the slot. The Option card fits

into this track.

CAUTION! Make sure the I/O card is inserted properly into the track to
avoid damaging the card's components.

3. Slide the card inside the plastic track and insert it into the slot. You will hear a click

when the card is fully inserted.

Be careful:

it is easy to miss the guide track. Refer

to Figure 11.1.

11.3: Configuring Option Cards

CAUTION! FOR PROPER OPERATION, RESET ALL PARAMETERS IN THE UNIT
AFTER HARDWARE MODIFICATION.

The Nexus® 1500+ meter auto-detects any Option cards installed in it. Configure the

Option cards through Communicator EXT

software. Refer to Chapter 11 of the

Communicator EXT

4.0 and MeterManager EXT Software User Manual

for detailed

instructions.

Summary of Contents for Shark 100T



































































































































































































































































































































Search results

Summary of Contents for Shark 100T

Reviews:

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 186 / 322

Search results

Summary of Contents for Shark 100T

Reviews: