manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 108 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 108

     

Doc

#    

E154713     

                              

              5-14

5: Communication Wiring

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Internal Clock Crystal

•  The Nexus® 1500+ meter is equipped with an internal clock crystal that is accurate 

to 3.5 ppm, or less than 10 seconds per month drift, and which can be used if IRIG-
B is not connected and/or Line Frequency Clock Synchronization is not enabled.

•  The meter has a battery backup that is used for the real time clock, only, in case of 

a power outage. The battery is a Panasonic BR3032, which is rated at 500 mAh and 
which has a battery life of at least ten years. A Low Batt message is displayed on 
the status bar of the Communicator EXT™ software's Main screen (see Section 
2.2.2 of the 

Communicator EXT

TM

 4.0 and MeterManager EXT Software User Manual 

for details) when the battery is equal to or less than 2.55 volts, which is still well 
within the operating range of the clock component. It is recommended that you 
change the battery within three months after the Low Batt message appears. 
Contact EIG’s customer service and support department at phone number 516-
334-0870 (or fax number 516-338-4741) for battery replacement instructions. 

SNTP (Simple Network Time Protocol)

•  With SNTP you access a Network Time Protocol (NTP) Server for time synchroniza-

tion. The NTP server can be either a device with a real-time clock that is networked 
with your meter, or an NTP server on the Internet. You can configure SNTP time 
synchronization for either the standard or the optional Ethernet card. SNTP config-
uration is done in the Device Profile. Refer to Chapter 11 of the 

Communicator 

EXT

TM

 4.0 and MeterManager EXT Software User Manual 

for instructions.

DNP Time Synchronization

•  Using Communicator EXT

TM

 software, you can set the meter to request time 

synchronization from the DNP Master. Requests can be made from once per minute 
to once per day. See the 

Nexus® 1252/1262/1272/1500/1500+ DNP User Manual 

for instructions. You can download the manual from EIG’s website: 
www.electroind.com/dl_page.html.

Other Time Setting Tools

•  

Tools>Set Device Time

: for manual or PC Time Setting

•  

Script & Scheduler

: time Stamps Retrieved Logs and Data

•  

MV90

: can synchronize time on retrievals in the form of a time stamp; refer to the 

Communicator EXT

TM

 4.0 and MeterManager EXT Software User Manual

 (HHF 

Converter) for more MV-90 details.

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments