manualshive.com logo in svg

Electro Industries/GaugeTech Shark 100T, Installation & Operation Manual, Page: 137 / 322

Share
Download
Electro Industries/GaugeTech Shark 100T Installation & Operation Manual Download Page 137

     

Doc

#    

E154713     

                              

              7-3

7: Transformer Loss Compensation

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro 

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

The Values for %LWFE, %LWCU, %LVFE, and %LVCU are derived from the trans-

former and meter information, as demonstrated in the following sections. 

The calculated loss compensation values are added to or subtracted from the mea-
sured Watts and VARs. The selection of adding or subtracting losses is made through 
the meter's profile when programming the meter (see the following section for 
instructions). The meter uses the combination of the add/subtract setting and the 
directional definition of power flow (also in the profile) to determine how to handle the 
losses. Losses will be "added to" or "subtracted from" (depending on whether add or 
subtract is selected) the Received Power flow. For example, if losses are set to "Add 
to" and received power equals 2000 kW and losses are equal to 20 kW then the total 
metered value with loss compensation would be 2020 kW; for these same settings if 
the meter measured 2000 kW of delivered power the total metered value with loss 
compensation would be 1980 kW. 

Since transformer loss compensation is the more common loss compensation method, 
the meter has been designed for this application. Line loss compensation is calculated 
in the meter using the same terms but the percent values are calculated by a different 
methodology.

7.2: Nexus® 1500+ Meter's Transformer Loss Compensation 

•  Performs calculations on each phase of the meter for every measurement taken; 

unbalanced loads are handled accurately. 

•  Calculates numerically, eliminating the environmental effects that cause inaccura-

cies in electromechanical compensators.

•  Performs bidirectional loss compensation.

•  Requires no additional wiring; the compensation occurs internally. 

•  Imposes no additional electrical burden when performing loss compensation.

VAR

TotalTransfomerLoss

VA

TransformerFullScale

%LVFE

Vmeasured

Vnominal

-----------------------------

4

%LVCU

Imeasured

Inominal

----------------------------

2

+

=

Summary of Contents for Shark 100T



































































































































































































































































































































Reviews:

No comments