Eaton Power Xpert PXM 4000, User And Installation Manual

Page: 257 / 292

www.eaton.com
IM02601004E
Page 249
E Option Cards
E.2. Optional I/O Card
The Power Xpert Meter can be equipped with an optional Discrete Input/Output (IO) card.
The PXMIO-B card can be ordered with a new meter or as an field upgrade. This card
includes 8 discrete inputs, 2 solid sate outputs, 3 relay outputs and a test LED.
For field upgrade, de-energize equipment to prevent shock hazard.
The meter includes sensitive electronic components. Caution should be used to avoid
electrostatic discharge to prevent equipment damage.
1. Disconnect control power and verify that the health LED is no longer flashing before
proceeding.
2. Remove power supply card after the health LED stops flashing
3. Remove the main communications board and optional CE card or blank filler plate.
4. Carefully insert I/O card using card slot provided. Care should be taken that the card
alignment is correct before seating the card into the connector socket.
5. Secure with screws at top and bottom.
6. Reassemble the CE card or blank filler plate and main communications and power sup -
ply, securing retaining screws on all cards.This card provides for external discrete I/O
interfacing.
S1 LED
Meter Test LED (Follows state of S1)
S1 Solid State Form A Output
S2 Solid State Form A Output
Max Load: 100mA
Max Voltage: 30V
R1 Form C Relay Output
R1A Normally Open/R1B Normally Closed
R2 Form C Relay Output
R2A Normally Open/R2B Normally Closed
R3 Form C Relay Output
R3A Normally Open/R3B Normally Closed
240 VAC
30Vdc
Max 5 Amp
DI1 - DI8
Discrete Inputs
Self sourced: 24Vdc ~10mA/input
24Vdc Internal Source
DIS
Discrete Input Source
6
PXMIO-B
5A 240VAC
30VD
C
9
8
7
SELF SOURC
E
24VD
C
5
4
3
2
IO3-
1
100m
A
30VD
C
4
IO2-
3
2
1
69
8
7
5
34
1
IO1-
2
R2B
R3B
R3C
R3A
R2A
R2C
R1B
R1C
S21
R1A
S22
S12
S11
DI6
DIS
DI8
DI7
DI5
DI4
DI3
DI1
DI2
CW
S1 LED
10VA Source MAX
PXCM-5
TXD RXD
C
24+
SH
SH
DB
DA
CM6-
3
2
1
CM5-
3
2
1
Com 0 Display
10VA Source MAX
C
24+
SH
CM4-
3
2
1
Com 1 RS485
TXD RXD
SH
DB
DA CM3-
3
2
1
RXD/TXD
10/100 T (RJ45)
Local Configuration
Link
CM
1
CW
CE
4
PXCE-B
100 Fx (ST)
LAN/WAN
10/100 T (RJ45)
TXD/RXD
Com 2 RS485
Link
Com 3 RS232
1
CE3-
23
DA
RXD TXD
DTE
TXD RXD
SH
DB
CE
2
Tx
CE1-
Rx
CW
Address
Base
15
13
1
3
5
Health
11
CW
9
7
Status
Short
Warning!
unplugging
CT's before
CW
PS1-
100-240VAC
PXPS-1
110-250VDC
50W Max
47-63 Hz
2
1 (+) L
(-) N
Rating
DO NOT HIPOT / DIELECTRIC TEST
AVERTISSEMENT: CET EQUIPEMENT RENFERME PLUSIEURS
REMOVE POWER BEFORE SERVICING
3 G
CIRCUITS SOUS TENSION. VOIR LE SCHEMA.
MORE THAN ONE LIVE CIRCUIT. SEE DIAGRAM.
WARNING
CW
for technical support
1-800-809-2772 or 1-414-449-7100
www.EatonElectrical.com
Customer Satisfaction
<http://www.EatonElectrical.com
2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
E185559
MEASURING EQUIPMENT
20NL