Dodge 2010 Caliber Owner'S Manual Download Page 403 | Manualshive

Page: 403 / 470

background image

when the pads are replaced. However, low fluid level
may be caused by a leak and a checkup may be needed.

NOTE:

If your vehicle is equipped with a

manual

transaxle

, the brake fluid reservoir supplies fluid to both

the brake system and the clutch release system. The two
systems are separated in the reservoir, and a leak in one
system will not affect the other system. The

manual

transaxle

clutch release system should not require fluid

replacement during the life of the vehicle. If the brake
fluid reservoir is low and the brake system does not
indicate any leaks or other problems, it may be a result of
a leak in the hydraulic clutch release system. See your
local authorized dealer for service.

Use only manufacturer’s recommended brake fluid. Re-
fer to “Fluids, Lubricants, and Genuine Parts” in “Main-
taining Your Vehicle” for further information.

WARNING!

•

Use only manufacturer’s recommended brake
fluid. Refer to “Fluids, Lubricants, and Genuine
Parts” in “Maintaining Your Vehicle” for further
information. Using the wrong type of brake fluid
can severely damage your brake system and/or
impair its performance. The proper type of brake
fluid for your vehicle is also labeled on the origi-
nal factory installed hydraulic master cylinder
reservoir.

(Continued)

402

MAINTAINING YOUR VEHICLE

«
...
401
402
403
404
405
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Jabra Pages: 10

Brand: Quadratec Pages: 8

21 COVERT Series

Brand: Code 3 Pages: 16

Brand: GMC Pages: 20

Brand: Fiat Pages: 172

Brand: Honda Pages: 6

Brand: AC Schnitzer Pages: 20

Brand: BMW Pages: 38

Brand: iDataLink Pages: 6

Escalade 2004 Escalade ESV

Brand: Cadillac Pages: 472

Brand: Kia Pages: 233

Brand: Mercedes-Benz Pages: 585

Brand: WABCO Pages: 224

Brand: Porsche Pages: 127

Brand: v.link Pages: 19

Brand: Vauxhall Pages: 4

2018 GRAND CHEROKEE

Brand: Jeep Pages: 372

Brand: BMW Pages: 242

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands