Dodge 2010 Caliber Owner'S Manual Download Page 158 | Manualshive

Page: 158 / 470

background image

•

After training a HomeLink

威

channel, if the garage

door does not operate with HomeLink

威

and the ga-

rage door opener was manufactured after 1995, the
garage door opener may have a rolling code. If so,
proceed to the heading “Programming A Rolling Code
System.”

4. Press and hold the just-trained HomeLink

威

button

and observe the indicator light.

If the indicator light stays on constantly, programming is
complete and the garage door (or device) should activate
when the HomeLink

威

button is pressed.

If the indicator light blinks rapidly for two seconds, and
then turns to a constant light, continue with program-
ming for a Rolling Code.

5. PROGRAMMING A ROLLING CODE SYSTEM

At the garage door opener motor (in the garage), locate
the “Learn” or “Training” button.

This can usually be found where the hanging antenna
wire is attached to the garage door opener motor (it is
NOT the button normally used to open and close the
door).

1 — Garage Door Opener
2 — Training Button

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

157

«
...
156
157
158
159
160
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: A-Tach Mounts Pages: 2

Brand: Chevrolet Pages: 412

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Brand: Dakota Digital Pages: 3

Brand: Whispbar Pages: 17

Brand: Skoda Pages: 281

Brand: Mitsubishi Pages: 19

Brand: Motoalliance Pages: 5

Brand: Draw tite Pages: 4

Brand: Prorack Pages: 15

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Brand: ADS Pages: 25

Brand: Jeep Pages: 374

Brand: SAFARI Pages: 5

Brand: Kolpin Pages: 6

Brand: Porsche Pages: 145

Full Display Mirror

Brand: Gentex Pages: 18

Pro Competition

Brand: G-Tech Pages: 180

Brand: Yakima Pages: 12

Brand: Kargo Master Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands