Dodge 2010 Caliber Owner'S Manual Download Page 242 | Manualshive

Page: 242 / 470

background image

SALES CODE RES/RSC — AM/FM STEREO
RADIO WITH CD PLAYER (MP3 AUX JACK) AND
SIRIUS RADIO

NOTE:

The radio sales code is located on the lower right

side of the radio faceplate.

Operating Instructions — Radio Mode

NOTE:

The ignition switch must be in the ON or ACC

position to operate the radio.

Power Switch/Volume Control (Rotary)

Push the ON/VOLUME control knob to turn on the
radio. Push the ON/VOLUME control knob a second
time to turn off the radio.

Electronic Volume Control

The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the
ON/VOLUME control knob to the right increases the
volume and to the left decreases it.

When the audio system is turned on, the sound will be
set at the same volume level as last played.

SEEK Buttons

Press and release the SEEK buttons to search for the next
listenable station in AM/FM mode. Press the right switch

RES/RSC Radio

4

UNDERSTANDING YOUR INSTRUMENT PANEL

241

«
...
240
241
242
243
244
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Ranger design Pages: 6

Brand: Daihatsu Pages: 340

Brand: Jeep Pages: 322

Brand: Jeep Pages: 341

Brand: Jeep Pages: 310

Brand: Jeep Pages: 189

Brand: Jeep Pages: 26

Brand: Jeep Pages: 21

Brand: Jabra Pages: 10

Brand: Yakima Pages: 4

Brand: Carefree Pages: 12

Brand: Thule Pages: 2

Truck Training Model

Brand: WABCO Pages: 56

Brand: AEM Pages: 27

Brand: AIS Pages: 2

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Needit Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands