Dodge 2010 Caliber Owner'S Manual Download Page 165 | Manualshive

Page: 165 / 470

background image

Ignition Off Operation

The sunroof will also operate up to 45 seconds after the
ignition has been turned OFF. The sunroof operation will
be canceled if either of the front doors are opened during
the 45 second time period.

ELECTRICAL POWER OUTLETS

There is a standard 12 Volt (13 Amp) power outlet located
in the instrument panel for added convenience. This
power outlet can power cellular phones, electronics and
other low power devices.

Power is available when the ignition switch is in the ON
or ACC position. Insert the cigar lighter or accessory plug
into the outlet for use.

To preserve the heating element,

do not hold the lighter in the heating position.

12 Volt Power Outlet

164

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
163
164
165
166
167
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Horn Tools Pages: 6

Brand: Kia Pages: 51

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

Brand: Anker Technology Pages: 8

Brand: Prorack Pages: 15

Brand: Mobridge Pages: 20

Brand: Cadillac Pages: 19

Brand: Prime Design Pages: 8

Brand: Mercedes-Benz Pages: 305

S90 TWIN ENGINE

Brand: Volvo Pages: 662

Brand: HUSKY LINERS Pages: 4

Brand: iOttie Pages: 19

Brand: v.link Pages: 20

iDatalink Maestro RR

Brand: Automotive Data Solutions Pages: 139

Brand: Guardsman Pages: 3

Brand: Split Phantom Pages: 20

Brand: Echomaster Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands