Dodge 2010 Caliber Owner'S Manual Download Page 306 | Manualshive

Page: 306 / 470

background image

several ignition cycles, and the vehicle has been driven
several miles (kilometers) at speeds greater than 30 mph
(48 km/h), see your authorized dealer as soon as possible
to have the problem diagnosed and corrected.

NOTE:

•

The “ESC Off Indicator Light” and the “ESC Malfunc-
tion Indicator Light” come on momentarily each time
the ignition switch is turned ON.

•

Each time the ignition is turned ON, the ESC system
will be ON even if it was turned off previously.

•

The ESC system will make buzzing or clicking sounds
when it is active. This is normal; the sounds will stop
when ESC becomes inactive following the maneuver
that caused the ESC activation.

ESC Operating Modes

The ESC system has two available operating modes.

Full On

This is the normal operating mode for ESC. Whenever
the vehicle is started the ESC system will be in this “On”
mode. This mode should be used for most driving
situations. ESC should only be turned to “Partial Off” for
specific reasons as noted below.

Partial Off

This mode is entered by momentarily pressing the “ESC
Off” switch. This mode is intended to be used if the
vehicle is in deep snow, sand or gravel conditions and
more wheel spin than ESC would normally allow is
required to gain traction.

To turn ESC on again, momentarily press the “ESC Off”
switch. This will restore the normal “ESC On” mode of
operation.

5

STARTING AND OPERATING

305

«
...
304
305
306
307
308
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Porsche 911 Turbo S Wheel

Brand: FANATEC Pages: 9

Brand: HALE Pages: 44

Brand: IAME Pages: 17

Brand: Saab Pages: 10

Brand: Pacbrake Pages: 14

Brand: Yakima Pages: 12

CB-796IG2-CIGD-R

Brand: CARRYBOY Pages: 4

Brand: GMC Pages: 428

Brand: MAXWORKS Pages: 7

Brand: JKS Pages: 3

Brand: Thule Pages: 12

Brand: Lexus Pages: 82

Brand: Kargo Master Pages: 9

Brand: Haltech Pages: 12

Brand: Audiovox Pages: 2

Brand: ECS Electronics Pages: 14

Brand: AL-KO Pages: 88

1967 Calais Coupe

Brand: Cadillac Pages: 255

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands