Dodge 2010 Caliber Owner'S Manual Download Page 160 | Manualshive

Page: 160 / 470

background image

successfully accepted the frequency signal. The indica-
tor light will flash slowly and then rapidly when fully
trained.

If you unplugged the device for training, plug it back in
at this time.

Then proceed with Step 4 under “Programming
HomeLink

威

” earlier in this section.

Using HomeLink

姞

To operate, press and release the programmed
HomeLink

威

button. Activation will now occur for the

trained device (i.e., garage door opener, gate operator,
Security system, entry door lock, home/office lighting,
etc.,). The handheld transmitter of the device may also be
used at any time.

Reprogramming A Single HomeLink

姞

Button

To reprogram a channel that has been previously trained,
follow these steps:

1. Turn the ignition switch to the ON/RUN position.

2. Press and hold the desired HomeLink

威

button until

the indicator light begins to flash after 20 seconds.

Do not

release the button.

3.

Without releasing the button,

proceed with Program-

ming HomeLink

威

Step 2 and follow all remaining steps.

Security

It is advised to erase all channels before you sell or turn
in your vehicle.

To do this, press and hold the two outside buttons for
20 seconds until the red indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.

The HomeLink

威

Universal Transceiver is disabled when

the Vehicle Security Alarm is active.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

159

«
...
158
159
160
161
162
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Jackco Pages: 11

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: Mazdaspeed Pages: 8

Dodge Charger TufBox

Brand: TUFLOC Pages: 6

Brand: Whispbar Pages: 77

Brand: Doug Thorley Headers Pages: 5

Brand: Edelbrock Pages: 2

Brand: IBASE Technology Pages: 100

S2000 Windscreen Camera Mount

Brand: Modifry Products Pages: 2

Brand: Metra Electronics Pages: 8

Brand: BMW Pages: 38

Brand: Thule Pages: 8

Brand: MULTILIFT Pages: 62

2005 JR41 Stratus

Brand: Dodge Pages: 293

Brand: Caltrend Pages: 3

Brand: Weltmann KFZ-Teile Pages: 12

OVER DRIVE PolyPRO 3 Car Cover

Brand: Classic Accessories Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands