Dodge 2010 Caliber Owner'S Manual Download Page 145 | Manualshive

Page: 145 / 470

background image

light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.

High/Low Beam Switch

Push the multifunction lever away from you to switch
the headlights to high beam. Pull the multifunction lever
toward you to switch the headlights back to low beam.

Flash-to-Pass

You can signal another vehicle with your headlights by
lightly pulling the multifunction lever toward you. This
turn on the high beam headlights until the multifunction
lever is released.

NOTE:

If the multifunction lever is held in the flash-to-

pass position for more than 30 seconds, the high beams
will shut off. If this occurs, wait 30 seconds for the next
flash-to-pass operation.

Instrument Panel Dimmer

Rotate the center portion of the lever to the extreme
bottom position to fully dim the instrument panel lights
and prevent the interior lights from illuminating when a
door is opened.

Rotate the center portion of the lever up to increase the
brightness of the instrument panel lights when the park-
ing lights or headlights are on.

Rotate the center portion of the lever upward to the next
detent position to brighten the odometer and radio when
the parking lights or headlights are on.

Rotate the center portion of the lever upward to the last
detent to turn on the interior lighting.

144

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
143
144
145
146
147
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Victory 4x4 Pages: 13

5TH GEN 4RUNNER

Brand: Victory 4x4 Pages: 5

Brand: Keith Pages: 2

Brand: Saab Pages: 288

Brand: Sunsky Pages: 9

Brand: UAZ Pages: 90

Brand: Gator Pages: 8

Brand: benbat Pages: 14

Brand: SPL Pages: 5

Brand: Subaru Pages: 44

Brand: Motoalliance Pages: 4

Brand: SIXTOL Pages: 32

Brand: SuperATV Pages: 2

Brand: KAP Pages: 22

2002 Accord Coupe

Brand: Honda Pages: 367

Brand: Opel Pages: 44

Brand: Setma Pages: 16

Brand: Laser Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands