Dodge 2010 Caliber Owner'S Manual Download Page 40 | Manualshive

Page: 40 / 470

background image

WARNING! (Continued)

•

Wearing your belt in the wrong place could make
your injuries in a collision much worse. You might
suffer internal injuries, or you could even slide out
of part of the belt. Follow these instructions to
wear your seat belt safely and to keep your pas-
sengers safe, too.

•

Two people should never be belted into a single
seat belt. People belted together can crash into one
another in an accident, hurting one another badly.
Never use a lap/shoulder belt or lap belt for more
than one person, no matter what their size.

Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and
adjust the seat.

2. The seat belt latch plate is along side the pillar near the
back of your seat. Grasp the latch plate and pull out the
belt. Slide the latch plate up the webbing as far as
necessary to allow the belt to go around your lap.

Pulling Out the Latch Plate

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

39

«
...
38
39
40
41
42
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Green Motion DC 22

Brand: Eaton Pages: 65

Brand: Jeep Pages: 322

Brand: Jeep Pages: 341

Brand: Jeep Pages: 310

Brand: Jeep Pages: 189

Brand: Jeep Pages: 26

Brand: Jeep Pages: 21

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: Victory 4x4 Pages: 13

Brand: Rola Pages: 3

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: Oldsmobile Pages: 2

Brand: M7 SPEED Pages: 6

Brand: Hank Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands