Dodge 2010 Caliber Owner'S Manual Download Page 282 | Manualshive

Page: 282 / 470

background image

If Engine Fails to Start

If the engine fails to start after you have followed the
“Normal Starting” or “Extreme Cold Weather” proce-
dures, it may be flooded. Push the accelerator pedal all
the way to the floor and hold it there. Crank the engine
for no more than 15 seconds. This should clear any excess
fuel in case the engine is flooded. Leave the ignition key
in the ON position, release the accelerator pedal and
repeat the “Normal Starting” procedure.

WARNING!

Never pour fuel or other flammable liquid into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in flash fire causing
serious personal injury.

CAUTION!

To prevent damage to the starter, do not crank the
engine for more than 15 seconds at a time. Wait 10 to
15 seconds before trying again.

After Starting

The idle speed will automatically decrease as the engine
warms up.

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms engine coolant and
permits quicker starts in cold weather. Connect the cord
to a standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.

5

STARTING AND OPERATING

281

«
...
280
281
282
283
284
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Jeep Pages: 673

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: Ford Pages: 2

Brand: BESAFE Pages: 4

Brand: Whispbar Pages: 85

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Mercedes-Benz Pages: 39

Brand: travall Pages: 2

Brand: Gacell Pages: 12

Brand: Anker Technology Pages: 8

Brand: JSPORT Pages: 2

Brand: Jaeger Pages: 16

Nova Electronics Hide-a-Led DEUCE DUAL HEAD W600

Brand: Ecco Pages: 2

Aura Mobile BT MCP-2014

Brand: Spracht Pages: 2

Brand: FAAFTECH Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands