Dodge 2010 Caliber Owner'S Manual Download Page 194 | Manualshive

Page: 194 / 470

background image

“gATE” and “Oil Change Required” will only be dis-
played in the EVIC display. For additional information,
refer to “Electronic Vehicle Information Center (EVIC) —
If Equipped”.

gASCAP

If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, a
“gASCAP” message will display in the odometer display
area. Tighten the fuel filler cap properly and press the
TRIP ODOMETER button to turn off the message. If the
problem continues, the message will appear the next time
the vehicle is started.

A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).

LoW TirE

When tire pressure is low, the odometer display will
toggle between LoW and TirE for three cycles.

noFUSE

If the vehicle diagnostic system determines that the
Ignition Off Draw (IOD) fuse is improperly installed, or
damaged, a “noFUSE” message will display in the odom-
eter display area. For further information on fuses and
fuse locations refer to “Fuses” in “Maintaining Your
Vehicle”.

CHAngE OIL

Your vehicle is equipped with an engine oil change
indicator system. The “CHAngE OIL” message will flash
in the instrument cluster odometer for approximately
12 seconds after a single chime has sounded to indicate
the next scheduled oil change interval. The engine oil
change indicator system is duty cycle based, which
means the engine oil change interval may fluctuate
dependent upon your personal driving style.

Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN

4

UNDERSTANDING YOUR INSTRUMENT PANEL

193

«
...
192
193
194
195
196
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Jeep Pages: 6

Brand: Camoplast Pages: 60

Brand: Kia Pages: 385

Brand: Phonocar Pages: 6

Brand: THIEYE Pages: 88

Brand: Kia Pages: 680

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Seat Pages: 300

Even Brake 9400

Brand: Roadmaster Pages: 20

Hitch-Haul 30110315

Brand: Masterbuilt Pages: 2

Brand: Metra Electronics Pages: 17

Brand: SkyRack Pages: 2

Brand: Gator Pages: 18

Brand: Ecco Pages: 11

Brand: J Communications Pages: 10

2012 CIVIC SEDAN HF

Brand: Honda Pages: 8

1991 CAMRY Body Section

Brand: Toyota Pages: 111

Brand: Chevrolet Pages: 362

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands