Dodge 2010 Caliber Owner'S Manual Download Page 375 | Manualshive

Page: 375 / 470

background image

Manual Transaxle

•

Front Wheel Drive (FWD) or All Wheel Drive (AWD)
vehicles can be flat towed (all four wheels on the
ground) with the transmission in NEUTRAL.

•

FWD vehicles can be towed with the front wheels
elevated.

•

FWD or AWD vehicles can be towed on a flatbed truck
(all wheels off the ground).

All Transaxles

If it is necessary to use the accessories while being towed
(wipers, defrosters, etc.), the key must be in the ON
position, not the ACC position. Make certain the trans-
mission remains in NEUTRAL.

CAUTION!

•

If the vehicle being towed requires steering, the
ignition switch must be in the ACC position, not
in the LOCK position.

•

Do not attempt to use sling-type equipment when
towing. When securing the vehicle to a flatbed
truck, do not attach to front or rear suspension
components. Damage to your vehicle may result
from improper towing.

374

WHAT TO DO IN EMERGENCIES

«
...
373
374
375
376
377
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 2

Brand: Cadillac Pages: 494

Brand: Cadillac Pages: 500

Brand: Cadillac Pages: 40

Brand: Cadillac Pages: 432

Brand: Cadillac Pages: 338

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 438

NPL-TV 7874 DIGITAL

Brand: Napoli Pages: 20

Brand: Ford Pages: 12

ESCALADE FAMILY - SPECIFICATIONS 2011

Brand: Cadillac Pages: 1

Brand: Chevrolet Pages: 2

Brand: Cadillac Pages: 518

Brand: Opel Pages: 141

Brand: TAUBENREUTHER Pages: 8

Electra 225 1965

Brand: Buick Pages: 914

Brand: travall Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands