Dodge 2010 Caliber Owner'S Manual Download Page 285

Page: 285 / 470

CAUTION!

If you skip more than one gear while downshifting
or downshift at too high a vehicle speed, you could
damage the engine, transaxle, or clutch.

To maintain a safe speed and prolong brake life, shift
down to second or first gear when descending a steep
grade.

When turning a corner or driving up a steep grade,
downshift early so that the engine will not be
overburdened.

AUTOMATIC TRANSAXLE — IF EQUIPPED

NOTE:

The Continuously Variable Automatic Transaxle

(CVT) changes ratios in a continuous manner. This may
sometimes

⬙

feel

⬙

as if it is slipping, but this is normal and

does not harm anything.

CAUTION!

Damage to the transaxle may occur if the following
precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

•

Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.

•

Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed.

•

Before shifting into any gear, make sure your foot
is firmly on the brake pedal.

NOTE:

You MUST press and hold the brake pedal down

while shifting out of PARK.

284

STARTING AND OPERATING

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Search results

Summary of Contents for 2010 Caliber

Reviews:

Related manuals for 2010 Caliber

Brands by name

Popular brands

Dodge 2010 Caliber, Owner'S Manual

Search results

Summary of Contents for 2010 Caliber

Reviews:

Related manuals for 2010 Caliber

Brands by name

Popular brands