Dodge 2010 Caliber Owner'S Manual Download Page 365

Page: 365 / 470

Jacking Instructions

WARNING!

Carefully follow these tire changing warnings to help
prevent personal injury or damage to your vehicle:

•

Always park on a firm, level surface as far from
the edge of the roadway as possible before raising
the vehicle.

•

Block the wheel diagonally opposite the wheel to
be raised.

•

Set the parking brake firmly and set an automatic
transmission in PARK; a manual transmission in
REVERSE.

•

Never start or run the engine with the vehicle on a
jack.

•

Do not let anyone sit in the vehicle when it is on a
jack.

(Continued)

WARNING! (Continued)

•

Do not get under the vehicle when it is on a jack.

•

Only use the jack in the positions indicated and
for lifting this vehicle during a tire change.

•

If working on or near a roadway, be extremely
careful of motor traffic.

•

To assure that spare tires, flat or inflated, are
securely stowed, spares must be stowed with the
valve stem facing the ground.

•

Turn on the Hazard Warning flasher.

Jack Warning Label

364

WHAT TO DO IN EMERGENCIES

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Search results

Summary of Contents for 2010 Caliber

Reviews:

Related manuals for 2010 Caliber

Brands by name

Popular brands

Dodge 2010 Caliber, Owner'S Manual

Search results

Summary of Contents for 2010 Caliber

Reviews:

Related manuals for 2010 Caliber

Brands by name

Popular brands