Dodge 2010 Caliber Owner'S Manual Download Page 374 | Manualshive

Page: 374 / 470

background image

CAUTION! (Continued)

•

Revving the engine or spinning the wheels too fast
may lead to transmission overheating and failure.
It can also damage the tires. Do not spin the
wheels above 30 mph (48 km/h) while in gear (no
transmission shifting occurring).

WARNING!

Fast spinning tires can be dangerous. Forces gener-
ated by excessive wheel speeds may cause damage, or
even failure, of the axle and tires. A tire could
explode and injure someone. Do not spin your vehi-
cle’s wheels faster than 30 mph (48 km/h) or for
longer than 30 seconds continuously without stop-
ping when you are stuck and do not let anyone near
a spinning wheel, no matter what the speed.

TOWING A DISABLED VEHICLE

With Ignition Key

Automatic Transaxle

•

Front Wheel Drive (FWD) vehicles can be towed with
the front wheels elevated or on a flatbed truck (all four
wheels off the ground).

•

All Wheel Drive (AWD) vehicles must be towed on a
flatbed truck (all four wheels off the ground).

CAUTION!

DO NOT flat tow any vehicle equipped with an
automatic transmission. Damage to the drivetrain
will result.

6

WHAT TO DO IN EMERGENCIES

373

«
...
372
373
374
375
376
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Saab Pages: 75

Brand: Happy Orange Pages: 2

Brand: Falcon Pages: 8

Brand: Jabra Pages: 10

Brand: GARO Pages: 23

LS4 Wallmounted

Brand: GARO Pages: 15

2011 Corolla LE

Brand: Toyota Pages: 19

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Spiral Audio Pages: 2

Brand: Park-Daddy Pages: 22

Brand: Skoda Pages: 281

Fleetwood Brougham Sedan 1966

Brand: Cadillac Pages: 56

Brand: Volvo Pages: 18

Brand: TOP VEHICLE TECH Pages: 8

Brand: Mercedes-Benz Pages: 24

Brand: Kargo Master Pages: 17

Brand: Buick Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands