Dodge 2010 Caliber Owner'S Manual Download Page 341 | Manualshive

Page: 341 / 470

background image

NOTE:

Intentional tampering with emissions control sys-

tems can result in civil penalties being assessed against you.

Carbon Monoxide Warnings

WARNING!

Carbon monoxide (CO) in exhaust gases is deadly.
Follow the precautions below to prevent carbon
monoxide poisoning:

•

Do not inhale exhaust gases. They contain carbon
monoxide, a colorless and odorless gas which can
kill. Never run the engine in a closed area, such as
a garage, and never sit in a parked vehicle with the
engine running for an extended period of time. If
the vehicle is stopped in an open area with the
engine running for more than a short period,
adjust the ventilation system to force fresh, out-
side air into the vehicle.

(Continued)

WARNING! (Continued)

•

Guard against carbon monoxide with proper
maintenance. Have the exhaust system inspected
every time the vehicle is raised. Have any abnor-
mal conditions repaired promptly. Until repaired,
drive with all side windows fully open.

•

Keep the liftgate closed when driving your vehicle
to prevent carbon monoxide and other poisonous
exhaust gases from entering the vehicle.

ADDING FUEL

Fuel Filler Cap (Gas Cap)

The gas cap is behind the fuel filler door, on the left side
of the vehicle. If the gas cap is lost or damaged, be sure
the replacement cap is for use with this vehicle.

340

STARTING AND OPERATING

«
...
339
340
341
342
343
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Reference Series

Brand: OEM Audio Pages: 29

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: Metra Electronics Pages: 4

REARSIGHT OnStar 250-8822

Brand: Rostra Pages: 2

Brand: U & Me Brothers Pages: 6

Brand: Kia Pages: 54

Brand: Hyundai Pages: 19

RVS systems RVS-M641

Brand: Safe Fleet Pages: 24

Brand: Cadillac Pages: 2

Brand: Buick Pages: 20

LED Dominator TAM83S2

Brand: Whelen Engineering Company Pages: 2

Brand: KLAUS Multiparking Pages: 72

Brand: Xpresskit Pages: 12

Performer-Plus 2172

Brand: Edelbrock Pages: 4

Brand: Cadillac Pages: 438

Brand: ROLEC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands