Dodge 2010 Caliber Owner'S Manual Download Page 280 | Manualshive

Page: 280 / 470

background image

STARTING PROCEDURES

Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts.

WARNING!

Never leave children alone in a vehicle. Leaving
unattended children in a vehicle is dangerous for a
number of reasons. A child or others could be seri-
ously or fatally injured. Do not leave the key in the
ignition. A child could operate power windows,
other controls, or move the vehicle.

Manual Transaxle – If Equipped

Before starting the engine fully apply the parking brake,
press the clutch pedal to the floor, and place the shift
lever in NEUTRAL.

NOTE:

•

The engine will not start unless the clutch pedal is
pressed to the floor.

•

If the key will not turn and the steering wheel is
locked, rotate the wheel in either direction to relieve
pressure on the locking mechanism and then turn the
key.

Automatic Transaxle – If Equipped

The shift lever must be in the PARK or NEUTRAL
position before you can start the engine. Apply the brakes
before shifting to any driving gear.

NOTE:

You must press the brake pedal before shifting

out of PARK.

Tip Start

NOTE:

Normal starting of either a cold or a warm

engine is obtained without pumping or pressing the
accelerator pedal.

5

STARTING AND OPERATING

279

«
...
278
279
280
281
282
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Valeo Pages: 17

Brand: iDataLink Pages: 9

Brand: Jeep Pages: 12

Brand: Jeep Pages: 6

Brand: Saab Pages: 10

ESCALADE FAMILY - SPECIFICATIONS 2011

Brand: Cadillac Pages: 1

Brand: Ultra-tow Pages: 14

Brand: Mercedes-Benz Pages: 121

Brand: Menabo Pages: 8

Brand: Camtree Pages: 5

adaptiv mini ADVM-BM1

Brand: Connects2 Pages: 4

Brand: Jeep Pages: 16

Brand: Audi Pages: 4

Brand: M7 SPEED Pages: 6

Truck Diesel Supplement 2012

Brand: RAM Pages: 174

Brand: Subaru Pages: 298

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands