Dodge 2010 Caliber Owner'S Manual Download Page 368 | Manualshive

Page: 368 / 470

background image

WARNING!

To avoid possible personal injury, handle the wheel
covers with care to avoid contact with any sharp
edges.

NOTE:

The wheel cover is held on the wheel by the

wheel nuts. When reinstalling the original wheel, prop-
erly align the wheel cover to the valve stem, place the
wheel cover onto the wheel, then install the wheel nuts.

7. Lower the vehicle by turning the jack screw to the left.

8. Finish tightening the nuts. Push down on the wrench
while tightening the wheel nuts. Alternate nuts until each
nut has been tightened twice. The correct wheel nut
torque is 100 ft lbs (135 N·m). If you doubt that you have
tightened the nuts correctly, have them checked with a
torque wrench by your authorized dealer or service
station.

9. Remove the wheel blocks and lower the jack until it is
free. Reassemble the lug wrench to the jack assembly and
stow it in the spare tire area. Secure the assembly using
the means provided.

WARNING!

A loose tire or jack thrown forward in a collision or
hard stop could endanger the occupants of the ve-
hicle. Always stow the jack parts and the spare tire in
the places provided.

10. Place the deflated (flat) tire in the cargo area,

have the

tire repaired or replaced as soon as possible.

6

WHAT TO DO IN EMERGENCIES

367

«
...
366
367
368
369
370
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: AAMP of America Pages: 6

Brand: Yakima Pages: 7

Brand: Yakima Pages: 6

Brand: Yakima Pages: 10

Brand: Yakima Pages: 12

Brand: U & Me Brothers Pages: 6

Brand: Yakima Pages: 21

DBALL2-HYUNDAI9

Brand: Xpresskit Pages: 13

2011 3500 Chassis Cab

Brand: RAM Pages: 92

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Kuda Pages: 3

Truck Diesel Supplement 2012

Brand: RAM Pages: 174

ADARAC Aluminum M Series

Brand: aci Pages: 16

Brand: Imiola HAK-POL Pages: 3

Brand: v.LOGiC Pages: 22

Brand: Acura Pages: 7

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands