Dodge 2010 Caliber Owner'S Manual Download Page 336 | Manualshive

Page: 336 / 470

background image

will be displayed instead of dashes. A system fault can
occur with any of the following scenarios:

1. Jamming due to electronic devices or driving next to
facilities emitting the same radio frequencies as the TPM
sensors.

2. Installing some form of aftermarket window tinting
that affects radio wave signals.

3. Snow or ice around the wheels or wheel housings.

4. Using tire chains on the vehicle.

5. Using wheels/tires not equipped with TPM sensors.

NOTE:

Your vehicle is equipped with a compact spare

wheel and tire assembly.

1. The compact spare tire does not have a tire pressure
monitoring sensor. Therefore, the TPMS will not monitor
the tire pressure in the compact spare tire.

2. If you install the compact spare tire in place of a road
tire that has a pressure below the low-pressure warning
limit, upon the next ignition key cycle, a chime will
sound and the Tire Pressure Monitoring Telltale Light
will still turn ON due to the low tire.

3. However, after driving the vehicle for up to 20 min-
utes above 15 mph (25 km/h), the Tire Pressure Moni-
toring Telltale Light will flash on and off for 75 seconds
and then remain on solid. In addition, the EVIC will
display a “CHECK TPM SYSTEM” message for three
seconds and then display dashes (- -) in place of the
pressure values.

4. For each subsequent ignition key cycle, a chime will
sound and the Tire Pressure Monitoring Telltale Light
will flash on and off for 75 seconds and then remain on
solid, and the EVIC will display a “CHECK TPM SYS-
TEM” message for three seconds and then display dashes
(- -) in place of the pressure values.

5

STARTING AND OPERATING

335

«
...
334
335
336
337
338
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Camcar Pages: 2

Brand: Whispbar Pages: 77

Brand: Mitsubishi Pages: 19

Brand: Flash Cover Pages: 2

Brand: Porsche Pages: 98

2011 SRX CROSSOVER

Brand: Cadillac Pages: 416

Brand: TIE DOWN Pages: 2

Brand: Jeep Pages: 292

Brand: Thule Pages: 2

Brand: Edelbrock Pages: 2

Brand: Mercedes-Benz Pages: 93

Prestige 128-8602

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 18

Brand: FIRRAK Pages: 12

Brand: QA1 Pages: 4

Brand: Curtis Pages: 5

Brand: Macally Pages: 10

Brand: DIGITAL DELAY Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands