Dodge 2010 Caliber Owner'S Manual Download Page 369 | Manualshive

Page: 369 / 470

background image

WARNING!

A loose tire thrown forward in a collision or hard
stop could injure the occupants in the vehicle. Have
the deflated (flat) tire repaired or replaced immedi-
ately.

11. Check the tire pressure as soon as possible. Correct
the tire pressure as required.

JUMP-STARTING PROCEDURES

If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.

NOTE:

When using a portable battery booster pack

follow the manufacturer’s operating instructions and
precautions.

CAUTION!

Do not use a portable battery booster pack or any
other booster source with a system voltage greater
than 12 Volts or damage to the battery, starter motor,
alternator or electrical system may occur.

WARNING!

When temperatures are below the freezing point,
electrolyte in a discharged battery may freeze. Do not
attempt jump-starting because the battery could rup-
ture or explode and cause personal injury. Battery
temperature must be brought above the freezing
point before attempting a jump-start.

368

WHAT TO DO IN EMERGENCIES

«
...
367
368
369
370
371
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Saab Pages: 75

Brand: TATA Motors Pages: 156

Brand: Mercedes-Benz Pages: 368

Brand: Mercedes-Benz Pages: 358

Brand: cam Pages: 28

Brand: Cadillac Pages: 20

Brand: Carcomm Pages: 2

Brand: JSPORT Pages: 2

Brand: Ford Pages: 52

INDICA eV2 XETA CNG

Brand: TATA Motors Pages: 24

Brand: PAC Pages: 5

Brand: Percon Pages: 49

Brand: Z Flash Pages: 4

Brand: true-i Pages: 11

Brand: Lock'er Down Pages: 2

Full Display Mirror

Brand: Gentex Pages: 18

Brand: Ranger design Pages: 14

Brand: Whispbar Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands