Dodge 2010 Caliber Owner'S Manual Download Page 123 | Manualshive

Page: 123 / 470

background image

General Information

This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:

•

Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.

•

This device may not cause harmful interference.

•

This device must accept any interference received,
including interference that may cause undesired
operation.

VOICE COMMAND SYSTEM — IF EQUIPPED

Voice Command System Operation

This Voice Command system allows you to
control your AM, FM radio, satellite radio, disc
player, and a memo recorder.

NOTE:

Take care to speak into the Voice Interface

System as calmly and normally as possible. The ability of
the Voice Interface System to recognize user voice com-
mands may be negatively affected by rapid speaking or a
raised voice level.

WARNING!

Any voice commanded system should be used only
in safe driving conditions following local laws and
phone use. All attention should be kept on the
roadway ahead. Failure to do so may result in an
accident causing serious injury or death.

When you press the Voice Command

button, you

will hear a beep. The beep is your signal to give a
command.

122

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
121
122
123
124
125
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: JAC Pages: 70

Brand: Daihatsu Pages: 41

Brand: Daihatsu Pages: 268

Brand: Toyota Pages: 56

Brand: iArmor Pages: 6

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: minnid Pages: 44

Brand: hc-cargo Pages: 60

Brand: walser Pages: 24

Brand: Fab Fours Pages: 19

Brand: Cadillac Pages: 20

Brand: Omix-Ada Pages: 6

Brand: Black Horse Off Road Pages: 7

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: Fab Fours Pages: 21

Quantum Wash'n'Wipe N30208

Brand: National Cycle Pages: 12

Brand: Pontiac Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands